Parallel Line IP (PLIP) is a cheap way to
network when you want to connect only two machines. It uses a parallel port
and a special cable, achieving speeds of 10 kilobytes per second to 20 kilobytes per second.
PLIP was originally developed by Crynwr, Inc. Its design at the time was
rather ingenious (or, if you prefer, a
hack), because the original parallel ports on
IBM PCs were designed to spend their time being unidirectional printer ports;
the eight data lines could be used only to send data from the PC to the
peripheral device, but not the other way around.[1] The Cyrnwr
PLIP design worked around this limitation by using the port's five
status lines for input, which limited it to transferring all data as
nibbles (half bytes) only, but allowed for bidirectional
transfer. This mode of operation was called PLIP “mode 0.”
Today, the parallel ports supplied on PC hardware cater to full
bidirectional 8-bit data transfer, and PLIP has been extended to
accomodate this with the addition of PLIP “mode 1.”
Linux kernels up to and including Version 2.0 support PLIP mode 0 only,
and an enhanced parallel port driver exists as a
patch against the 2.0 kernel and as a
standard part of the 2.2 kernel code to provide PLIP mode 1 operation, too.
[2]
Unlike earlier versions of the PLIP code, the driver now attempts to be
compatible with the PLIP implementations from Crynwr, as well as the PLIP
driver in NCSA telnet.[3]
To connect two machines using PLIP, you need a special cable sold at some
shops as a Null Printer or Turbo Laplink cable.
You can, however, make one yourself fairly easily;
Appendix B shows you how.
The PLIP driver for Linux is the work of almost countless persons. It is
currently maintained by Niibe Yutaka.[4]
If compiled into the kernel, it sets up a network interface for each of the
possible printer ports, with plip0 corresponding to
parallel port lp0, plip1
corresponding to lp1, etc. The mapping of interfaces to
ports differs in the 2.0 kernels and the 2.2
kernels. In the 2.0 kernels, the mapping was hardwired in the
drivers/net/Spacd.c file in the kernel
source. The default mappings in this file are:
If you configured your printer port in a different way, you
must change these values in drivers/net/Space.c in
the Linux kernel source and build a new kernel.
In the 2.2 kernels, the PLIP driver uses the “parport” parallel port
sharing driver developed by Philip Blundell.[5] The new driver allocates the PLIP network device names serially,
just as for the Ethernet or PPP drivers, so the first PLIP device created is
plip0, the second is plip1, and so on.
The physical parallel port hardware is also allocated serially. By default, the
parallel port driver will attempt to detect your parallel port hardware with an
autoprobe routine, recording the physical device information in the order found. It is better practice to explicitly tell the kernel the physical I/O
parameters. You can do this by supplying arguments to the
parport_pc.o module as you load it, or if you have
compiled the driver into your kernel, using lilo to supply
arguments to the kernel at boot time. The IRQ setting of any device may be
changed later by writing the new IRQ value to the related
/proc/parport/*/irq file.
Configuring the physical I/O parameters in a 2.2 kernel when loading the
module is straightforward. For instance, to tell the driver that you have
two PC-style parallel ports at I/O addresses 0x278 and
0c378 and IRQs 5 and 7, respectively, you would load the
module with the following arguments:
modprobe parport_ pc io=0x278,0x378 irq=5,7 |
The corresponding arguments to pass to the kernel for a compiled-in driver are:
parport=0x278,5 parport=0x378,7 |
You would use the lilo
append
keyword to have these arguments
passed to the kernel automatically at boot time.
When the PLIP driver is initialized, either at boot time if it is
built-in, or when the plip.o module is loaded,
each of the parallel ports will have a plip
network device associated with it. plip0 will be
assigned to the first parallel port device, plip1
the second, and so on. You can manually override this automatic
assignment using another set of kernel arguments. For instance, to
assign parport0 to network device
plip0, and parport1 to network
device plip1, you would use kernel arguments of:
plip=parport1 plip=parport0 |
This mapping does not mean, however, that you cannot use these parallel ports
for printing or other purposes. The physical parallel port devices are used
by the PLIP driver only when the corresponding interface is configured
up.
