| -h |
Options help |
|---|
| -itype | string
Input file type (optional). If set to raw, this
indicates that the input file does not have a header. While
this can be used to specify file types other than raw, this is
rarely used for other purposes
as the file type of all the existing supported
types can be determined automatically from the
file's header. If the input file is unheadered,
files are assumed to be shorts (16bit).
Supported types are
nist, est, esps, snd, riff, aiff, audlab, raw, ascii |
|---|
| -n | int
Number of channels in an unheadered input file |
|---|
| -f | int
Sample rate in Hertz for an unheadered input file |
|---|
| -ibo | string
Input byte order in an unheadered input file:
possibliities are: MSB , LSB, native or nonnative.
Suns, HP, SGI Mips, M68000 are MSB (big endian)
Intel, Alpha, DEC Mips, Vax are LSB (little
endian) |
|---|
| -iswap |
Swap bytes. (For use on an unheadered input file) |
|---|
| -istype | string
Sample type in an unheadered input file:
short, mulaw, byte, ascii |
|---|
| -c | string
Select a single channel (starts from 0).
Waveforms can have multiple channels. This option
extracts a single channel for progcessing and
discards the rest. |
|---|
| -start | float
Extract sub-wave starting at this time, specified in
seconds |
|---|
| -end | float
Extract sub-wave ending at this time, specified in
seconds |
|---|
| -from | int
Extract sub-wave starting at this sample point |
|---|
| -to | int
Extract sub-wave ending at this sample point |
|---|
| -L |
Perform low pass filtering on input. This option should always
be used in normal processing as it usually increases
performance considerably |
|---|
| -P |
perform peak tracking |
|---|
| -fmin | float
miniumum F0 value. Sets the minimum allowed F0 in
output track. Default is 40.000.
Changing this to suit the speaker usually increases
performance. Typical recommended values are 60-90Hz for
males and 120-150Hz for females |
|---|
| -fmax | float
maxiumum F0 value. Sets the maximum allowed F0 in
output track. Default is 400.000.
Changing this to suit the speaker usually increases
performance. Typical recommended values are 200Hz for
males and 300-400Hz for females |
|---|
| -shift | float
frame spacing in seconds for fixed frame analysis.
This doesn't have to be the same as the output file spacing -
the -S option can be used to resample the track before saving
default: 0.005 |
|---|
| -length | float
analysis frame length in seconds.
default: 0.010 |
|---|
| -lpfilter | int
Low pass filter, with cutoff frequency in Hz
Filtering is performed by a FIR filter which is built at run
time. The order of the filter can be given by -forder. The
default value is 199 |
|---|
| -forder | int
Order of FIR filter used for lpfilter and
hpfilter. This must be ODD. Sensible values range
from 19 (quick but with a shallow rolloff) to 199
(slow but with a steep rolloff). The default is 199. |
|---|
| -d | float
decimation factor
set down-sampling for quicker computation so that only one in
decimation factor samples are used in the first instance.
Must be in the range of one to ten inclusive. Default is four.
For data sampled at 10kHz, it is advised that a decimation
factor of two isselected. |
|---|
| -n | float
Inoise floor.
Set the maximum absolute signal amplitude that represents
silence to Inoise floor. If the absolute amplitude of
the first segment in a given frame is below this level at all
times, then the frame is classified as representing silence.
Must be a positive number. Default is 120 ADC units. |
|---|
| -h | float
unvoiced to voiced coeff threshold
set the correlation coefficient threshold which must be
exceeded in a transition from an unvoiced classified frame
of speech to a voiced frame as the unvoiced to voiced coeff
threshold. Must be in the range zero to one inclusive.
Default is 0.88. |
|---|
| -m | float
min voiced to unvoiced coeff threshold
set the minimum allowed correlation coefficient threshold
which must not be exceeded in a transition from a voiced
classified frame of speech to an unvoiced frame, as
min voiced to unvoiced coeff threshold. Must be in the
range zero to unvoiced to voiced coeff threshold
inclusive. Default is 0.75. |
|---|
| -r | float
voiced to unvoiced coeff threshold-ratio
set the scaling factor used in determining the correlation
coefficient threshold which must not be exceeded in a voiced
frame to unvoiced frame transition, as voiced to unvoiced
coeff threshold -ratio. The voiced to unvoiced coefficient
threshold is determined by multiplying this scaling factor
with the maximum cross-correlation coefficient of the
previously voiced frame. If this product is less than
min voiced to unvoiced coeff threshold then this is used
instead. Must be in the range zero to one inclusive.
Default is 0.85. |
|---|
| -t | float
anti pitch doubling/halving threshold
set the threshold used in eliminating (as far as possible)
pitch doubling and pitch halving errors as anti pitch
double/halving threshold. Must be in the range zero to
one inclusive. Default is 0.77. |
|---|
| -otype | string
" {ascii}"
Output file type, if unspecified ascii is
assumed, types are: none, esps, est, est_binary, htk, htk_fbank, htk_mfcc, htk_user, htk_discrete, xmg, xgraph, ema, ema_swapped, ascii, label |
|---|
| -S | float
Frame spacing of output in seconds. If this is
different from the internal spacing, the contour is
resampled at this spacing |
|---|
| -o | ofile
Output filename, defaults to stdout |
|---|
